Presscontrol Pump Pressure Controller
Di uno scrittore di uomini misteriosi
Descrizione
The Presscontrol is an electronic device for control and protection of the pump equipped with automatic restart in case of failure and anti jamming
The Presscontrol is an electronic device for control and protection of the pump equipped with automatic restart in case of failure and anti jamming function. It can be energised at either 115 Vac or 230 Vac. Starts and stops the pump depending on opening and closing of the taps. Stops the pump in case of a water shortage and protects it from dry running. Is equipped with automatic restart in case of failure and anti-jamming function. Can be installed on surface and submersible pumps. No need for an expansion tank, check valve, filter or fittings. Maintenance free. INSTALLATION AND STARTUP The device can be installed directly on the pump or between the pump and the first tap. Make all the electrical connections, check that the pump is correctly primed, open a tap and energize. The green Power on Led will light up on the control panel and the pump will start (yellow Pump on Led on) and will keep running for several seconds to pressurize the system. If this time is insufficient, the device will stop the pump (redFailure led on). Press and hold down the Restart button until the red Failure led turns off and the water comes out of the open tap. When the tap is closed, the pump will stop after a few seconds (yellow Pump on led turns off). From now on, the device will turn the pump on and off depending on the opening and closing of the tap. In case of water shortage, the device will stop the pump and protect it from dry running (red Failure led on). In case of a temporary blackout, the device will automatically rearm once the electricity returns. AUTOMATIC RESTART AND ANTI-JAMMING FUNCTION In case of stopping due to a water shortage, the device will automatically make 10 double attempts to rearm over the 24 hours following the failure, each lasting approximately 5seconds to allow the pump and the system to reload if possible. The user can try to rearm the device at any time by pressing the Restart button. If for any reason the pump remains idle for 24 consecutive hours, the device will carry out a start-up of the pump motor for about 5 seconds. On request, the device can be supplied with: - Wired electrical cables. - R version with adjustable restart pressure between 1.5 and 3 bar. The full technical data sheet can be viewed by clicking here. Should you prefer to checkout using PayPal then simply add the product to your cart as normal, select checkout securely and from the order summary page select the Alternative Payment Methods button at the top right. We do also accept telephone orders so if you would prefer to make payment over the telephone by card then please do not hesitate to call us and one of our friendly engineers will be happy to assist.
The Presscontrol is an electronic device for control and protection of the pump equipped with automatic restart in case of failure and anti jamming function. It can be energised at either 115 Vac or 230 Vac. Starts and stops the pump depending on opening and closing of the taps. Stops the pump in case of a water shortage and protects it from dry running. Is equipped with automatic restart in case of failure and anti-jamming function. Can be installed on surface and submersible pumps. No need for an expansion tank, check valve, filter or fittings. Maintenance free. INSTALLATION AND STARTUP The device can be installed directly on the pump or between the pump and the first tap. Make all the electrical connections, check that the pump is correctly primed, open a tap and energize. The green Power on Led will light up on the control panel and the pump will start (yellow Pump on Led on) and will keep running for several seconds to pressurize the system. If this time is insufficient, the device will stop the pump (redFailure led on). Press and hold down the Restart button until the red Failure led turns off and the water comes out of the open tap. When the tap is closed, the pump will stop after a few seconds (yellow Pump on led turns off). From now on, the device will turn the pump on and off depending on the opening and closing of the tap. In case of water shortage, the device will stop the pump and protect it from dry running (red Failure led on). In case of a temporary blackout, the device will automatically rearm once the electricity returns. AUTOMATIC RESTART AND ANTI-JAMMING FUNCTION In case of stopping due to a water shortage, the device will automatically make 10 double attempts to rearm over the 24 hours following the failure, each lasting approximately 5seconds to allow the pump and the system to reload if possible. The user can try to rearm the device at any time by pressing the Restart button. If for any reason the pump remains idle for 24 consecutive hours, the device will carry out a start-up of the pump motor for about 5 seconds. On request, the device can be supplied with: - Wired electrical cables. - R version with adjustable restart pressure between 1.5 and 3 bar. The full technical data sheet can be viewed by clicking here. Should you prefer to checkout using PayPal then simply add the product to your cart as normal, select checkout securely and from the order summary page select the Alternative Payment Methods button at the top right. We do also accept telephone orders so if you would prefer to make payment over the telephone by card then please do not hesitate to call us and one of our friendly engineers will be happy to assist.
EPC 4 110V Automatic Water Pump Pressure Controller 10A Electronic Switch Control Pump Press Control IP65 10bar
PRESSCONTROL WATERTECH DA 1,5 - Eredi di Piazza Biagio di Piazza F. e C. sas
Automatic start and stop the pump when tap open/close. Reduce water hammer effects. Simple control to maintains constant pressure during operation. Dry running protection to protect motor, extra pump life. In order to avoid the pump on/off & pressure high/low problems. Description: /b br The electric switch is used in water systems, start and stop the pump automatically.
110V Automatic Electronic Switch Control Water Pump Pressure Controller for Water Pump
Presscontrol Automatic Pump Controller - Suitable for Water & Diesel Pumps
TOTAL Automatic Pump Control - TWPS101.How to installation Automatic Pump Control .
Protection operation: Stopping the pump when senses the lack of water flowing, preventing it from any damage dry operation Checks pressure : The
EPC 4 110V Automatic Water Pump Pressure Controller 10A Electronic Switch Control Pump Press Control IP65 10bar
Bathroom Solutions Ltd - This Pressure pump with Press Control or with a Pressure Switch and Pressure Tank. Both systems will automatically switch the the pump off in the absence of water
-1116-p.jpg?v=3702cd6b-ddbf-4b9a-bce7-4448c24b644d)
Presscontrol Pump Pressure Controller
Pentair Southern Cross Press Control Electronically Controlled Pressure Switch
Pressure Controller - Presscontrol PC22 – Pumps Australia
Water-proof Efficient And Requisite pressure control pump
da
per adulto (il prezzo varia in base alle dimensioni del gruppo)
